Description
What is the Standard Hopper Dryer for Injection Molding?
The Standard Hopper Dryer for Injection Molding DGMF-MOLD-CLAMPS-HD style is an industrial equipment hopper dryer injection molding machine supplied by DGMF Mold Clamps Co., Ltd. for the injection molding industries.
DGMF Standard Hopper Dryer for Injection Molding Descriptions
A hopper dryer can directly replace the ordinary hopper, relative to the ordinary hopper, the overall material uses stainless steel, high hardness, effective anti-corrosion, and anti-aging, to avoid contamination of raw materials caused by rust and corrosion, effectively increasing the service life.
Hopper dryer uses a PID intelligent temperature control meter to prevent temperature control errors and avoid causing damage to raw materials.
The drying hopper and base can be separated, easy to change materials, and clean. Hopper dryer machine with heat preservation layer, the use of special electronic heating tube, optimize the air intake, power saving rate of more than 30 plus percent.
Injection Molding Plastic Hopper Dryer Component Breakdown
All the hopper dryer parts components accessories can be purchased separately.
DGMF Standard Hopper Dryer for Injection Molding Features
1. Adopting P.I.D temperature control system, precise temperature control;
2. Special down-blowing air duct design, can evenly disperse hot air, keep the plastic dry, stable temperature, and improve drying efficiency;
3. Stainless steel double-layer heat preservation barrel with material window;
4. GHD-40U and above models are attached to open the view of the material door;
5. Thermal overload protection device, safe and reliable;
6. Novel appearance, bright appearance;
How does a hopper dryer work?
The wind blown out by the drying fan becomes high-temperature drying wind after drying the electric heater, and through the unique design of the down-blowing windpipe, the hot air is evenly dispersed in the holding barrel to dry the raw materials;
Optional hot air recovery device, the wind blown out after filtering and then blown out by the drying wind, forming a closed loop.
In the drying process, hot air with constant temperature is blown by the drying blower 2 of SHD into the drying hopper 7 to dry the materials.
Moisture will be separated and taken away by hot air, thus gaining a satisfied drying effect.
Air blown out of the blower via hot air pipe 4 became high-temperature drying air after being heated.
Through shade separator 5 and screen protector 6, hot air can be equably dispersed to the material in the storage tank (see picture).
Hot air recycler is optional so the air entered drying hopper 7 after being filtered by return air will get into the drying blower 2 to form a closed loop circle, which saves electricity.
DGMF Standard Hopper Dryer for Injection Molding Specifications
Injection Molding Machine Hopper Dryer Specifications |
||||
| SKU | D/MM | (H2+H3)*H3*H1/MM | Capacity | Power |
| DGMF-MOLD-CLAMPS-HD-12 | 330 | 600*390*658 | 12 KG | 2100 W |
| DGMF-MOLD-CLAMPS-HD-25 | 388 | 698*460*775 | 25 KG | 2700 W |
| DGMF-MOLD-CLAMPS-HD-50 | 460 | 882*570*885 | 50 KG | 3900 W |
| DGMF-MOLD-CLAMPS-HD-75 | 530 | 980*600*1140 | 75 KG | 4800 W |
| DGMF-MOLD-CLAMPS-HD-100 | 600 | 1025*665*885 | 100 KG | 7800 W |
| DGMF-MOLD-CLAMPS-HD-150 | 637 | 1215*865*1065 | 150 KG | 8900 W |
| DGMF-MOLD-CLAMPS-HD-200 | 747 | 1347*945*1305 | 200 KG | 10000 W |
| DGMF-MOLD-CLAMPS-HD-300 | 815 | 1513*1065*1460 | 300 KG | 15000 W |
| DGMF-MOLD-CLAMPS-HD-400 | 400 KG | |||
| DGMF-MOLD-CLAMPS-HD-600 | 600 KG | |||
| DGMF-MOLD-CLAMPS-HD-800 | 800 KG | |||
| DGMF-MOLD-CLAMPS-HD-1000 | 1000 KG | |||
Standard Hopper Dryer for Injection Molding Details
Details reflect quality
Sincerity in every detail
High-quality materials are used for both core and auxiliary components.
Intelligent digital display temperature controller
With an over-temperature sound and light alarm function, using a proportional deviation indicator thermostat can accurately control the temperature up to
Separate design of drying hopper barrel and hopper
Separate design of the material drying hopper barrel and hopper, quick change of material, easy to clear material, the hopper screen surface is flat and easy to clean to improve the efficiency of material change.
Visible material window
A transparent visual material window can be added on the front of the drying hopper so that you can check the condition of the material in the barrel at any time.
Full copper wire hopper dryer blower fan motor
Strong power, stable operation, low noise
Double-layer heat insulation for elbow
Thickened asbestos cloth + heat insulation cloth, environmental protection, energy saving, and high efficiency.
Precise temperature meter
High precision detection, stainless steel shell
Buckle-type over-temperature protection
When the temperature exceeds the set temperature, the machine will automatically cut off the power and stop heating to prevent the plastic from caking and the machine from being damaged.
DGMF Injection Molding 12 KG Standard Hopper Dryer
DGMF Injection Molding 25 KG Standard Hopper Dryer
DGMF Injection Molding 50 KG Standard Hopper Dryer
DGMF Injection Molding 100 KG Standard Hopper Dryer
DGMF Injection Molding 150 KG Standard Hopper Dryer
DGMF Injection Molding 200 KG Extra High Hopper Dryer
DGMF Injection Molding 200 KG Standard Hopper Dryer
DGMF Injection Molding 300 KG Standard Hopper Dryer
DGMF Injection Molding 400 KG Standard Hopper Dryer
DGMF Injection Molding 600 KG Standard Hopper Dryer
DGMF Injection Molding 800 KG Standard Hopper Dryer
DGMF Injection Molding 1000 KG Standard Hopper Dryer
etc.
Injection molding hopper dryer applications
Plastic injection molding hopper dryer can dry the raw materials that are wet due to packaging and transportation, used to remove the moisture on the surface, applicable to PP, PE, ABS, PVC, and other raw materials.
How to install the injection molding hopper dryer?
The direct installation method
The direct installation type is to mount the hopper dryer directly on the molding machine via a standard base. DGMF-MOLD-CLAMPS-HD-12 to DGMF-MOLD-CLAMPS-HD-300 is suitable for this mounting method as well as floor stand installation type; DGMF-MOLD-CLAMPS-HD-400 and models above should adopt floor stand installation type.
When using the method to mount the dryer, the equipped standard base must according to the material inlet diameter of the molding machine mounting drill holes. Then use the screw to fasten the base and the molding machine inlet.
The floor stand installation method
The floor stand installation type is to mount the dryer on a floor stand, then via a photo-sensor hopper receiver to convey the material to the feed port of a molding machine. DGMF-MOLD-CLAMPS-HD-400 and above models should adopt floor stand installation type.
The machine should be placed on a water-level floor to keep balance. If it is to be mounted on a high surface(e.g. on a scaffold or an interlayer), should ensure its structure and size can bear the weight and size of the machine.
DGMF Mold Clamps Co., Ltd supplies mold clamps, injection mold components, and machine tools.
Besides the injection molding hopper dryer, we supply the hopper dryer accessories such as hopper slide gate valves, hopper dryer blowers; hopper tanks, suction boxes, hopper dust collectors; hopper dryer heaters; screen separators, hopper dryer bases, cones, hot air pipes, hopper magnets, round and square grate magnets, control cabinets, magnetic sheet separators, stands, etc.
Contact us for the DGMF Mold Clamps Co., Ltd of the hopper dryer accessories you need.
